The Tacx Flux Smart Trainer came on the market in December 2016 and started arriving to US customers on December 27th. This trainer was a game changer this past fall, selling for roughly half the list price of similar direct drive trainers (discounted $709 price point during the Black Friday/Cyber Monday sales).
It became more concerning when Shane reported on December 17th that his #3396 replacement unit had failed (see 7min into video) with the same symptoms (slipping belt, burning rubber smell). He had inspected the internals of the unit and had not seen any apparent manufacturing differences from first unit. This unit had be carefully prepared by the company prior to delivery.
I received my early production unit in the 1st batch of units reaching US customers on 27Dec. It was a tough decision not to cancel the order given failure reports.
A Tacx Flux Owner Group created on Facebook discussed the issue. To their credit, Tacx provided a transparent summary of their assessment of the situation to the group on January 11th:
Since the launch of the FLUX (end of November) there have been some FLUX trainers with quality issues (1,7% of all produced FLUX trainers). These issues found their way back to our company through social media, influencers like Shane Miller and our support department. Questions are raised about the quality of the FLUX and some of you have concerns about your own FLUX or future FLUX. Hereby we’d like to clarify the situation and restore the confidence in the FLUX of current and potential FLUX owners.
After analyzing the products with a defect that were send back to our HQ, we concluded that the problems can be brought back to two main issues. Below we explain our findings.
The first issue was caused by the tensioning wheel that might be assembled too closely to the steel chassis. During a workout and especially during sprints this wheel is pushed against the steel chassis, causing internal damages and the transmission belt running of. This problem will occur within the first hours of use, if it doesn’t; your FLUX is ok.
Please note this problem didn’t occur during our durability and stress tests, which was the issue with Shane’s FLUX during his sprint. After the issue was noted and resolved we made the necessary adjustments to prevent this from happening on all future FLUX products.
The number of products that got into the market and might have this issue is small, the current return rate is 1,3% for this specific issue.
Analyzing the second issue was a bigger challenge as it was more difficult to reproduce this incident in order to find out what caused the belt to run of the pulley wheel. This second issue also occurred with a FLUX send to Shane Miller. When sending this second FLUX we double checked every assembly step to make sure this unit was perfect. Yet, this thoroughness has led to too much tension on the EDCO freewheel hub damaging the connector between the large metal pulley wheel and EDCO body. This weak spot cracked and caused a chain reaction displacing the large metal pulley wheel and letting the tensioning belt run of. This resulted in the grinding noise and smell noted in de video of Shane Miller. In order to prevent this issue from happening, we have tested the maximum torque on all the parts and adjusted this accordingly in the production process.
At the moment we only have a few cases with the same issue as Shane’s second FLUX. The vast majority of issues within this category is coming from the first issue.
Besides the first and second issue we encountered some minor other incidents, but no structural problems.
The current total amount of damaged FLUX trainers known to us is 1.7%, with the majority coming from the first production batch showing the first issue. We are confident that most FLUX trainers with issues from the first production batch are currently known.
What can you expect from Tacx?
We are very committed in solving FLUX issues as fast as possible so you can start training again. Therefor we kindly ask all FLUX users experiencing issues to send an email directly to firstname.lastname@example.org. We will take care of your problem by replacing your FLUX unit for a new one. It will be very helpful for us if you return the damaged FLUX units for analysis, as we would like to be sure that the causality of defects stays within the first and second issue.
DO NOT OPEN A FLUX YOURSELF!
This is very a dangerous process as high voltage runs through the electronics! Also, it can cause other problems when not reassembling it correctly, like broken magnets and electronics. Please note we can no longer guarantee warranty when you disassemble a Tacx product. But above all, please avoid dangerous situations.
We would like to express our sincere apologies to all those who’ve encountered FLUX issues. We’ll do everything we can to replace your broken unit.
We’ll proactively share all product issues encountered at Tacx and are as transparent as possible in doing so.
The Tacx Team
My unit (#230) failed after 47 miles.
Martin Smits, Business Development Manager from Tacx, subsequently shared on the DC Rainmaker blog comments that an “early unit” would be consider one with a serial number less than 1700.
Subsequently 70 failed units shared by customers in the Facebook Tacx Flux Owners Group and in comments on the DC Rainmaker blog Tacx Flux Trainer In Depth Review provided an emerging picture of the failure behavior of the unit. The initial reports were consistent with the summary from Tacx, but with subsequent failures occurring after 11Jan, the picture below has emerged:
There are many caveats to what can be inferred from isolated reports on the internet.
- How many high SN units are not in field?
- Are gaps in reported failure due to batches not in field or due to successful production?
- How many field units not ridden sufficiently?
- How many units not ridden at high wattage?
- How many failures not reported to FB group?
- Is reporting diminishing with late adopters?
Failure rates in various regions of production are noted on the plot.
- The reported failures run at 4.3% for 1st 500 units and then 2.6-6% for stretches under #2500.
- The failures appear to have persisted up to #2500 rather than the “early unit” 1700 threshold suggested by Tacx.
- Shane’s second failure came in a 7-unit, 2.2% failure rate stretch from #3300-3600. No belt slipping/burning smell failures have been reported since this period. Did Shane’s 2nd experience finally help resolve the issue for subsequent units?
- There is a 400 unit failure-free stretch prior to 3300. Tacx informed a customer with a unit in that range that it included manufacturing improvements, so one might speculate that were pulled back from distribution.
- Although the data hasn’t been reported and tabulated, many of the reported failures took longer than the 1 hour suggested by Tacx to occur, particularly for riders putting out less wattage.
- At least ninecustomers have reported 2 failed units and one customer has had 3. That could point to an inherent failure rate of around 6% or that failures are more likely with certain types of customers — those that take their units out of their boxes, ride them, and ride them at a high enough wattage to trigger failure.
- Over half the units have failures within 8 units of themselves. That also points to a true inherent failure rate of about 7%.
- Customers in EU have reported great customer service directly from Tacx and rapid direct replacements. The ocean has gotten in the way of that for international customers. Some early units remain on retailer shelves.
I was driven to do the analysis above by need to decide whether to seek a replacement as well as intellectual curiosity about how much the cycling community could infer about manufacturing quality issues from crowd-sourced failure data.
Given that replacements have been slow to arrive in the US as well as the unclear picture whether certain riders might be doomed to multiple failures, I opted to go with and Elite Drivo on 28Jan. I would consider a Flux for my spouse once the dust settles on this issue.
Seeing the emerging picture now that issues may have finally been resolved in production after the learning from Shane’s 2nd failure, I’m tempted to second guess that decision, but for now I’ll stick with the alternative but may consider a Flux as a 2nd unit for my spouse.
The picture is pretty clear for serial numbers under 3600, but not for those above. At this point the highest reported serial number in the wild is 4404. Seven people have reported working units in that range and no belt failures have been reported above 3600.